Book Title : Heat Transfer Calculations

Author(s) : Myer Kutz

Publisher : McGraw Hill

Pages : 727

Size : 9.5Mb

Book Description:

Heat Transfer Calculations by Myer Kutz e-book with easy procedures, calculations, enhancement techniques, formulas and rules of thumb. This convenient book gives you the tools to solve a broad section of problems dealing with subjects ranging from thermal industrial equipment to thermal properties of materials.

Table of Contents:

A. Contributors

B. Preface

**Part 1: Introductory Calculations**

1) Multi phase Films and Phase Change

2) Industrial Heat-Transfer Calculations

**Part 2: Steady-State Calculations**

3) Heat-Transfer and Temperature Results for a Moving Sheet Situated in a Moving Fluid

4) Solution for the Heat-Transfer Design of a Cooled Gas Turbine Airfoil

5) Steady-State Heat-Transfer Problem: Cooling Fin

6) Cooling of a Fuel Cell

7) Turbo generator Rotor Cooling Calculation

8) Heat Transfer through a Double-Glazed Window

**Part 3: Transient and Cyclic Calculations**

9) Use of Green’s Function to Solve for Temperatures in a Bi-material Slab Exposed to a Periodic Heat Flux Applied to Corrosion Detection

10) Lumped-Capacitance Model of a Tube Heated by a Periodic Source with Application to a PDE Tube

11) Calculation of Decoking Intervals for Direct-Fired Gas and Liquid Cracking Heaters

12) Transient Heat-Transfer Problem: Tape Pack Cooling

13) Calculation of the Transient Response of a Roof to Diurnal Heat Load Variations

14) Transient Heating of a Painted Vehicle Body Panel in an Automobile Assembly Plant Paint Shop Oven

15) Thermal System Transient Response

16) Thermal Response of Laminates to Cyclic Heat Input from the Edge

17) A Simple Calculation Procedure for Transient Heat and Mass Transfer with Phase Change: Moist Air Example

18) A Calculation Procedure for First- and Second-Law Efficiency Optimization of Refrigeration Cycles

19) Transient Analysis of Low Temperature, Low Energy Carrier

20) Parameter Estimation of Low Temperature, Low Energy Carrier

**Part 4: Heat-Transfer-Coefficient Determination**

21) Calculation of Convective Heat-Transfer Coefficient Using Semi-infinite Solid Assumption

22) Determination of Heat-Transfer Film Coefficients by the Wilson Analysis

**Part 5: Tubes, Pipes, and Ducts**

23) Calculation of Local Inside-Wall Convective Heat-Transfer Parameters from Measurements of Local Outside-Wall Temperatures along an Electrically Heated Circular Tube

24) Two-Phase Pressure Drop in Pipes

25) Calculations for Predicting Solids Deposition in Pipeline Transportation of Waxy Crude Oils

26) Heat Transfer in a Circular Duct

**Part 6: Heat Exchangers**

27) Air Cooling of a High-Voltage Power Supply Using a Compact Heat Exchanger

28) Energy Recovery from an Industrial Clothes Dryer Using a Condensing Heat Exchanger

29) Sizing of a Cross-flow Compact Heat Exchanger

30) Single-Phase Natural Circulation Loops

31) Evaluation of Condensation Heat Transfer in a Vertical Tube Heat Exchanger

32) Heat Exchanger Design Using an Evolutionary Algorithm

**Part 7: Fluidized Beds**

33) Fluidized-Bed Heat Transfer

**Part 8: Parameter and Boundary Estimation**

34) Estimation of Parameters in Models

35) Upper Bounds of Heat Transfer from Boxes

36) Estimating Freezing Time of Foods

**Part 9: Temperature Control**

37) Precision Temperature Control Using a Thermo-electric Module

**Part 10: Thermal Analysis and Design**

38) Thermal Analysis of a Large Telescope Mirror

39) Thermal Design and Operation of a Portable PCM Cooler

40) A First-Order Thermal Analysis of Balloon-Borne Air-Cooled Electronics

41) Thermal Analysis of Convectively Cooled Heat-Dissipating Components on Printed Circuit Boards

42) Design of a Fusion Bonding Process for Fabricating Thermoplastic-Matrix Composites

**Part 11: Economic Optimization**

43) Economic Optimization of Heat-Transfer Systems

44) Turkey Oven Design Problem